Turnkey Thread Gaging & Inspecting Systems

Our Standalone Stations are custom designed to fit your application and can handle any parts including those with multiple threads and different planes of orientation. They can be designed to run single parts or multiple parts with quick and convenient changeover and fed by any means (conveyor, track, hand loaded, robot loaded, robot served).

This Rotary Dial Station GO verifies internal threads in Round Nuts. The index wheel (dial plate) is at the center of the photo and the Thread-Verification Unit feeds down from the top. The machine is designed to run multiple part numbers and for quick changeover.

This vertically oriented dial indexing station tests Gear Blanks, for power seat mechanisms. The New Vista IND verifies the multi-start thread and measures the two trunnion-end diameters. Reject parts are sorted out.

This fully automated Dial Indexing Station is fed by a conveyor. The machine takes in two Oil filters at a time then performs a GO check, a NO GO for Pitch Diameter, and a NO GO for Minor Diameter. The parts are released back to the conveyor belt sorting the failed parts to the far edge of the belt.

This automated Dial Indexing Station GO verifies an internal M3 thread in circuit board spacers. Incoming parts are supplied by in-process feed tube, verified, then the good parts tube discharges parts in the correct orientation for next process step. Failed parts are collected in a reject bin.

This High-output thread-verification system for M12 external threads in plugs and M10 external threads in machine screws. Parts are fed in through a vibratory bowl feeder, GO verified then sorted into bins. Changeover between parts takes less than 5 minutes.

New-style Automated IND/SCC-MN-2 for brake system components. Supplied by a vibratory feeding system and Equipped with New Vista ‘Safety Indexer’ with quick-change index wheels. Good parts and reject parts go down separate tubes.

This fully automated Rotary Index Station taps and verifies grinder wheel hubs. Parts are fed by gravity through a track then tapped, cleaned, GO checked, NO GO checked, and sorted. It features a New Vista designed AR Tapping Unit

This station uses two of our single spindle STH Units to verify internal and external threads in Injector Bodies. It can be hand loaded or robot loaded. Designed to verify two different part numbers and can be changed over in under 3 minutes.

This station is built around one of our multiple spindle FLX Units to verify
three M5 threads in Ballnuts. Parts are taken from a conveyor, presented for verification, and finally sorted by which production line machined it. Rejects are placed in a lock box. This station can be tooled and fixtured for a second part in under 5 minutes.

This station built around four single spindle STH Units verifies 6 M10 threads in a large aluminum Extrusion. Each thread is GO verified for pitch and length and NO GO verified for minor diameter. Designed to be loaded by hand or a robot.

This station uses a single spindle STH Unit with a combination gage to GO and NO GO verify for pitch diameter an M10 thread in a single pass. Each thread is also NO GO tested for minor diameter. The station indexes through the 8 threads to complete verification. This station is hand loaded and could easily be configured for robot loading.

This fully automated high-speed station GO and NO GO verifies Oil Filters in groups of four. Cycle time is .6 seconds per filter. Parts are off loaded from a conveyor and good parts are returned to the conveyor. Parts that failed verification are offloaded to a reject conveyor.

This automated station takes parts that have been hand loaded into a magazine and feeds them one at a time for verification. In a single pass, four M4 threads are GO verified then failed parts are sorted into a locked box.

Features
Videos
Resources
Get a Quote

Can be fitted to Tap, Recondition, and Verify threads. Additionally, can accommodate other processes.
Automatically inspects threaded features in parts. Rejects are automatically sorted out.
Indexing wheel transfers part from load-in to various inspection positions.
Good parts and rejects are chuted away separately.
Throughputs to 14,400 parts per hour (four parts up).
Checks threaded holes (or external threads) by powering a Thread Gage Member into (or onto) the part. “GO” gaging, “NO GO” gaging, and combination gaging are all possible.
Sensitive high-speed drive causes the spindles to stop in case of missing, short or improperly formed threads. This creates a “reject” signal.
Will check blind holes accurately for thread depth.
Will not jam or stick in undersize (reject) threads. Rejects are separated out without stopping the process.
Does not subject the part (or the spindle) to high force or torque levels…even with a reject.
Multiple Spindle Stations are available for multiple parts or multiple centers work.
Automatic gaging of non-threaded features can be incorporated in.
Supplied tooled and proven out for your application.

Available as single-spindle Units, multiple-spindle Heads or complete Stations.
Used to form, verify or remediate threaded features utilizing the appropriate thread tools and Toolholders, by application.
With the right tooling, this system will simultaneously form, verify or remediate threads of different sizes and pitches.
Each Spindle can be individually set for applications with multiple torque and thread depth requirements.
Our Compliant Toolholders can be equipped to each spindle to ensure angular and positional compliance.
Strategically avoids damage from broken taps, missing or displaced holes with the use of New Vista’s patented clutch.
Protects against crossthreading and jamming.
Supplied perfectly tailored to your application’s needs.